sidekick said: I am new to the forum so have patients with me. i just purchased my shield 9mm plus and it has been working fine until i tried to break it down after shooting yesterday. the metal tab you see in the picture is stopping the slide from moving forward. I took a little screwdriver and pressed it down to get the slide all the way off.
Feb 2, 2021.
I would suggest using a plastic tipped hammer and just keep gently tapping the back of the slide as shown in the video and hopefully it will.
Jun 3, 2020.
It's best to pull the slide back all the way and let it go abruptly to send it forward. It will only move forward in that manner with a loaded.
1851 Colt Navy Revolver Cost $555.00, COLT GEN 2 1851 NAVY 36 CAL Cambridge, MN 55008 ; $365.00, UBERTI/ TAYLOR'S 1851 COLT NAVY. MPN FR18512. $299.99. Traditions 1851 Colt Navy .44Cal Black Powder Revolver – This fine reproduction of the Colt captures the original design. The authenticity is precise, from walnut grips to color case-hardened loading lever. Its cylinder carries
Are S&w 1911 Any Good 2,733 Posts. #2 · Aug nine, 2010. Springfield has exceptional fashions of 1911's which vary in rate from a bit over $500 up to $1300 in the manufacturing variety. Obviously the higher give up's just like the TRP and TM have extra features however the GI and Mil-Specs are also good weapons for the charge.
First check to see if there's anything obstructing the slide and preventing it from going forward. Then about the only thing you can do is tap the rear of the slide forward with a rubber mallet or something similar. You may want to squirt some type of lubricant in there first along all the contact points.
Moral of the story: DO NOT PRESS THE GRIP SAFETY WHILE DISASSEMBLING OR REASSEMBLING.
Shop Brownells For Smith & Wesson Shield Magazines,
Feb 3, 2020.
Make sure the magazine is removed, lock the slide back, rotate the takedown lever, move the slide forward until it stops, pull the trigger. It.
Rotate the take down lever counter-clockwise to the 3 o'clock position, release the slide stop and allow the slide back to its forward position. Now you are all done and your Smith & Wesson Shield EZ is fixed and ready to go to the range. Fix A Stuck Slide on a Smith & Wesson M&P Shield EZ 9mm Video. If you need step-by-step instructions on.
Review: Ruger LCP MAX – Once the recoil spring bottoms out and returns the slide forward, the two components lock.
machined-in offerings, not to mention low-light functionality. The U-notch rear is serrated to help.
Sep 9, 2017.
First check to see if there's anything obstructing the slide and preventing it from going forward. Then about the only thing you can do is tap.
Slide stop not working properly? Slide not coming off? Watch this detailed video on options to fix it yourself or to ship it in for Smith.
Slide locks back, rotate the slide release. Push down yellow sear bar with a pen/screwdriver and good to go. after break in you will not have to fight it as hard. rusty4269. 05-09-2014 05:22 AM. M&P Shield: Removing the Slide. The reason it won't lock is the slide isn't going back far enough.
If you remove the slide and lightly polish the slide stop with a fine nail file or really fine sandpaper (e.g. 600+ grit), it'll make it much easier to release the slide. It doesn't take much to remove the sharp edge of the slide stop so don't go overboard.
Feb 4, 2014. #1/14. I've always had this issue with my M&P. The slide release was always stiff and could never be fully disengaged without pressing down on both sides of the slide release button. Personally I would always press the slide release button down while pulling the slide back to put the slide forward and never really questioned it.
The Smith & Wesson Governor: A Versatile Z-Frame Revolver – When Smith & Wesson introduced the Governor in 2011.
If you already carry a duty-size gun, then the Governor will not be.
This is probably the easiest way to get the pin back in but it will not allow the slide to go all the way forward as in Image 4. IMAGE 4. The way to do this is make sure when you put the slide back on the weapon, you have the barrel as far forward as possible, as seen in Image 5. IMAGE 5. This way when you lock the pin in the slide will go all.
Jun 16, 2020.
You need to remove the slide again and adjust the recoil guide rod base. There is a rounded and a flat part of the base and the rounded part.
Mar 18, 2017.
Check for spurs in the slide . Make sure the recoil spring is installed straight . The slide stuck on mine stuck once after shooting a lot ,keep.
Primer drag and slide not locking back on Shield Plus. Close. 1. Posted by 8 months ago.
Smith & Wesson Firearms. Pictures, announcements, questions, accessories and tech. 37.8k. Members. 34. Online. Created Jul 1, 2012. Join. Top posts july 15th 2021 Top posts of july, 2021 Top posts 2021.
Only show this user. OK just got back from the range today and experienced a problem. I have about 300 rounds through my M&P .40. Loaded my weapon and after two rounds gun locked up.Slide did eject on second round. Could not rack slide but was able to push slide forward as slide did not close fully. I can only retract slide a quarter inch or so.
Normal. The follower on the magazine hold the slide open so the shooter knows the mag is empty and to change it. You can press down on the slide.
Problem #3 – SMITH & WESSON M&P SHIELD 9MM FEEDING ISSUE. Source: www.thehighroad.org. Another issue that can cross your way while using the Smith & Wesson M&P Shield 9mm pistol is the feeding issue. It can happen that the slide constantly locks back even with rounds still in the magazine. That can lead to the failure to extract, probably.
Jul 10, 2017.
The simple fix is to remove the back slide cover. It can be done with the slide on. Remove the striker if necessary. Sometimes just lifting the.
ShieldNS. I was trying to clean and lube my shield plus after a day at the range. I followed the manual procedure, but there seems to be an issue with the takedown lever – it will only rotate down about 60-70 degrees, and then stop. I just can't get it to go the full 90 degrees – I managed to get a blister on the tip of my thumb trying to move.